Message Us
MON-FRI 8AM-4PM EST
Message Us
MON-FRI 8AM-4PM EST
This is a brand new replacement shaft for the cutter assembly on the VCM 44 machines. This is the shaft only. Made from 100% stainless steel materi...
View full detailsThis is a direct replacement for your worn out or missing bottom feet. Made from tough, non-marking urethane material. The polyurethane composition...
View full detailsNew shaft sleeve for the VCM 40 and 44. Precision CNC machined from solid stainless steel for a precise fit. Recommended to change with every bowl ...
View full detailsReplacement stainless steel seal plate and gaskets for the HCM 300/450. In order for you to install this part you need: Have/had an existing seal ...
View full detailsNew stainless steel drum switch housing for the VCM 25 and 40. Tig welded construction and includes a pre-installed strain relief for the power cor...
View full detailsNew tilt lock pin and chain for the Hobart and Stephan VCM 40 and 25 machines. Replacement for the following OEM Part Numbers: - Hobart VCM 4...
View full detailsReplacement Sheeter Blade for the ANETS SDR-4 Measures 20-1/4" long and 2-1/4" wide Direct replacement for your OEM sheeter blades. Made from stro...
View full detailsNew knead/mix blade hub for the Hobart HCM 300/450. This blade hub is a direct replacement and comes standard with a 1 year free replacement warra...
View full detailsNew release lever for the Xebeco XeSRD20 dough dividers. This product is a genuine OEM product.
Replacement Sheeter Blades Set for the ANETS SDR-21, Two Pass Dough Roller These blades are used to remove dough from the rollers. Direct replace...
View full detailsNew wing nut for the VCM 44 knife cutter assembly. Stainless steel material with tig welded wings designed to move product out to the cutters.
This replacement bearing bolt is located in the swivel mechanism of the VCM 44. The swivel lock arm attaches to the face of this part. Over time th...
View full detailsThis food-grade white silicone seal is specifically designed to fit all models of the Stephan, Hobart VCM 40. It serves as a replacement for the or...
View full detailsNew replacement plastic knob for the VCM 25 and 40. This knob installs on four different locations on the VCM 25 and 40: Switch Handle Tilt Handl...
View full detailsNew two-piece spin off disk for the VCM 40 and 44. Protect your motor and upper bearing from water damage. This part will take the water that falls...
View full detailsReplacement Sheeter Blades Set for the ANETS SDR-42, Two Pass Dough Roller These blades are used to remove dough from the rollers. Direct replace...
View full detailsIntroducing the JPM QUAD CHOPPER! With our Quad Chopper assembly you'll be ready to slice and chop with a FOUR BLADE SETUP! This JPM Parts exclus...
View full detailsNew outer press plate for the Xebeco XeSRD20 dough dividers. Each divider uses 16 outer press plates and 4 inner plates.
It's becoming more common for the Stephan VCM 44 lids to crack on the square hinge tab. We designed a replacement tab that is made directly to the ...
View full detailsNew cellular rubber door gasket for the Stephan VCM 44 models. Also known as the "Seal Profile." Our gaskets are a direct OEM replacement and molde...
View full detailsDesigned to remove the (often stuck) nut on the bottom of the knife blade assembly. Precision laser cut from 304 stainless steel for long tern dura...
View full detailsNew set of wheels for the Hobart/Stephan VCM 40 and 25. Made from strong, white acetal plastic. Replacement for the following OEM Part Numbers:...
View full detailsStainless steel wrench set for removing and tightening the HCM 300/450 cutting assembly. Designed and manufactured by JPM. JPM Original Product
Introducing the NEW JPM QUAD CHOPPER! Special Introduction Pricing is Active! With our Quad Chopper assembly you'll be ready to slice and chop wi...
View full details